Vezi detalii
Romana
English
Deutsch
Francais
Magyar
Italiano
Espanol
Categorii
Promotii
Tricouri
Frecvent
Cumpărate împreună
Detalii produs
Descriere
Ham cu suport pentru câini de talie mare, pentru filmări din perspectiva animalului.
Double the wonderful moments.
Mount your Insta360 Ace, X or GO series camera on your dog's collar or back for two immersive angles.
Always steady.
Secure Back 3-Prong Base keeps Insta360 X series cameras locked in position.
On and off in a snap.
Easy to put on and remove thanks to bespoke snap-in design.
Durable, washable.
Constructed from outdoor sports material, the Pet Harness is easy to clean and difficult to damage. Use with a dog leash (sold separately) via the Leash Attachment on the mount.
Find the perfect fit.
Adjustable neck and belly straps ensure a secure, comfortable fit.
Compatibilitate: GO, ONE X, ONE R, ONE X2, GO 2, ONE RS (Twin/4K), ONE RS 1-Inch 360 Edition, ONE RS, X3, GO 3, Insta360 Ace Pro, Insta360 Ace, X4, GO 3S, Insta360 Ace Pro 2, X5, GO Ultra
Note de utilizare
- Ensure both the Neck Straps and Belly Straps are roughly the same length to keep the camera level and prevent tilting.
- To get the best filming results, ensure the Pet Harness Mount fits correctly. If it is too loose, the camera can tilt. Tighten the straps as much as possible while ensuring your dog is comfortable.
- If your dog shows any signs of discomfort or abnormal behavior, remove the Pet Harness Mount immediately.
- Install the camera exactly as shown in the instructions to prevent it from falling off.
- If you are not shooting in Back Perspective, remove the Back Base to reduce the weight of the harness and avoid potential accidents.
- The aspect ratio of GO 3S footage will be 16:9 when mounted horizontally and 9:16 when mounted vertically. The aspect ratio of GO 3 footage will not change if mounted horizontally or vertically; it needs to be set manually in the settings.
- After installing the Action Mount, ensure the top microphone and bottom speaker of GO 3S or GO 3 aren't covered to ensure optimal audio quality.
- When installing or removing GO 3S or GO 3, gently widen the Action Mount to fit the camera. Avoid stretching it too far to prevent deformation or breakage.
- The back of the camera is used for heat dissipation and can get hot. Avoid direct skin contact after use.
- If the 1/4" to 2-Prong Adapter, Standard Mount or Quick Release Mount slips or tilts while attached to the back base, install the Anti-Slip rings.
- The Anti-Tilt Accessory is recommended when using the Back 3-Prong Base. The Anti-Tilt Accessory is necessary when installing Insta360 X series cameras onto the Back 3-Prong Base.
- Once the Side Latch of the Riding Back Extension Support Rod Base is locked and the Extension Support Rod is set in place, do not apply force to the rod to avoid damaging it and the locking mechanism.
- If the Pet Harness Mount gets wet, wipe it clean before it has time to soak into the fabric then dry it either with a hair dryer set to cold or by leaving it in a cool, ventilated place.
- The Pet Harness Mount is not machine washable. If it gets dirty, wipe it clean with a wet towel and allow it to dry naturally in a cool, ventilated place. Do not soak or wash with bleach. Do not wring it out or leave it in the sun to dry.
Specificații
Caracteristici
Brand:
Insta360
Cod de bare (EAN):
6970357857821
Părerea clienților
Recenzii
Nu au fost găsite recenzii
Comunitatea Trisport
Întrebări & Răspunsuri
Întreabă comunitatea sau ajută alți sportivi — un răspuns aprobat îți aduce 10 puncte de fidelitate. Un review aprobat de cumpărător = 20 puncte.
Nicio întrebare încă la acest produs — fii primul care întreabă!
Intră în cont ca să întrebi sau să răspunzi — fără parolă, cu PIN pe email.
